Airbrush Introduction: Difference between revisions

Revision as of 11:43, 18 February 2024

This page is INCOMPLETE and still missing some important information before it can be used as a resource. Please use the "Discussion" feature above or talk to one of the tutors if you would like to help improve it. Thanks!

This is the content required for an introduction to our airbrush equipment . Reading this does NOT replace the mandatory session with a tutor! It will make it a lot quicker though ;-)

If you need this introduction, please reach out to the following tutors:

Health & Safety Precautions

Personal protection:


Danger	Description	Precautions
Aerosols	Airbrushing creates aerosols / vapours. Solvent-based AND water-based can cause pneumonia and other long-term lung problems.	use spray booth air extractor AND a respirator water-based colours: wear a mask with "P2" or even better "P3" filters when working with solvent-based colours: wear a mask with "A2" grade filters to protect against the solvent fumes. These "gas and vapour cartridges" have a use-by date and need to be replaced from time to time, according to the manufacturer's recommendations). wear goggles do not do any face painting
Paint	some paints may contain substances that are harmful to your skin	wear gloves
Airbrush needle	Every airbrush gun has a needle inside. The needle is usually covered/protected, but will become accessible when you disassemble the airbrush for cleaning.	handle with care never "poke" the front of the needle
Compressor	compressed air is generated and released through the airbrush: the airstream can damage eyes, ears and other sensible organs	do not point the airbrush at yourself or other people
Noise	Noise from the air extractor (the compressor is relatively quiet, and turns itself on/off depending on air pressure settings)	Noise protection gear
Spray Booth	The adjustable metal plate may bruise your fingers when reverted back to its vertical position.	Grab the metal plate on the left/right side, NOT underneath.
Paint fumes	Paint aerosols might travel away from the airbrush corner and cause damage to other equipment.	use spray booth close the curtain behind you

Practical Demonstration

show airbrush and needle functionality before connecting airbrush to compressor
connect airbrush to compressor
change compressor pressure settings
add paint / change paint / demonstrate how "thin" or "watery" the paint needs to be
spray examples with varying needle positions (fine line / area fill etc)
disconnect airbrush from compressor
empty compressor / use valve
disassemble airbrush
clean airbrush
reassemble airbrush

@@ Line 1: / Line 1: @@
 {{incomplete}}
-This is the content required for an introduction to our airbrush equipment. '''Reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
+This is the content required for an introduction to our [[Introduction for::Airbrush Compressor|airbrush equipment]] . '''Reading this does NOT replace the mandatory session with a [[tutor]]!''' It will make it a lot quicker though ;-)
-If you need this introduction, please reach out to the following tutors: [[Tutor::User:Björn|Björn]]
+If you need this introduction, please reach out to the following tutors:
 ===Health & Safety Precautions===
+[[PPE|Personal protection]]: [[File:Protection - goggles.svg|50px]] [[File:Protection - hearing.svg|50px]] [[File:Protection - gloves.svg|50px]]
 {| class="wikitable"
 |+
@@ Line 13: / Line 14: @@
 |-
 |Aerosols
-|Airbrushing creates aerosols / vapours. Although most airbrush paints are typically water-based, you don't want to inhale those aerosols / paint particles.
+|Airbrushing creates aerosols / vapours. Solvent-based AND water-based can cause pneumonia and other long-term lung problems.
-Solvent-based AND water-based can cause pneumonia and other long-term lung problems.
+|
-Masks with "P2" or even better "P3" filters are the minimum protective gear when working with water-based colours, as they'll protect you against paint particles.
+*use spray booth air extractor AND a respirator
-If you're using solvent-based colours, you should also wear a mask with "A2" grade filters to protect against the solvent fumes. (These "gas and vapour cartridges" have a use-by date and need to be replaced from time to time, according to the manufacturer's recommendations).
+*water-based colours: wear a mask with "P2" or even better "P3" filters when working with
-For example, here's the filter guide for 3M masks and filters: [https://multimedia.3m.com/mws/media/565214O/3m-cartridge-filter-guide-and-brochure.pdf English Version]– [http://multimedia.3m.com/mws/media/995779O/datenblatt-asd.pdf German Version]
+*solvent-based colours: wear a mask with "A2" grade filters to protect against the solvent fumes.
-|use spray booth air extractor AND a respirator mask (grade A2 P3) with a tight fit
+** These "gas and vapour cartridges" have a use-by date and need to be replaced from time to time, according to the manufacturer's recommendations).
-wear goggles / glasses
+* wear goggles
-do not do any face painting
+* do not do any face painting
 |-
 |Paint
@@ Line 28: / Line 29: @@
 |Airbrush needle
 |Every airbrush gun has a needle inside. The needle is usually covered/protected, but will become accessible when you disassemble the airbrush for cleaning.
-|Handle with care, never "poke" the front of the needle
+|
+*handle with care
+*never "poke" the front of the needle
 |-
 |Compressor
 | compressed air is generated and released through the airbrush:
-*the airstream can cause damage
+*the airstream can damage eyes, ears and other sensible organs
 |
 *do not point the airbrush at yourself or other people
@@ Line 42: / Line 45: @@
 |-
 |Spray Booth
-|The spray booth contains an adjustable metal plate, which is attached to two hinges at the top. When reverting the metal plate to its standard vertical position, make sure your fingers don't get caught.
+|The adjustable metal plate may bruise your fingers when reverted back to its vertical position.
 |Grab the metal plate on the left/right side, NOT underneath.
 |-
 |Paint fumes
-|Paint aerosols might travel away from the airbrush corner. We want protect our beautiful 3D-Printers.
+|Paint aerosols might travel away from the airbrush corner and cause damage to other equipment.
-|use spray booth;
+|
-close the curtain behind you
+*use spray booth
+*close the curtain behind you
 |}
 === Practical Demonstration===
 *show airbrush and needle functionality before connecting airbrush to compressor
 *connect airbrush to compressor